| 640-605 Remote Access 2.0 考试大纲 |
|
640-605 Remote Access 2.0 考试大纲 |
| 作者：佚名 来源：不详 更新：2006-8-25 21:05:35 错误报告 我要投稿 |
★Exam Description
The Remote Access exam (RMTAC 640-605) is one exam within two different
series of exams required to achieve either CCNP or CCDP Routing and Switching
★Exam Topics
The following topics are general guidelines for the content likely to be
included on the Remote Access exam. However, other related topics may also appear
■.Cisco Remote Access Networks Introduction
* Specify and /or identify the Cisco products that best meet the WAN
connection requirements for permanent or dialup access connections
■.Selecting CISCO Products for Remote Connections
* Explain and/or identify the advantages and disadvantages of WAN connection
* Select the appropriate WAN connection types that address specific site
* Select Cisco equipment that will suit the specific needs of a WAN topology
■.Assembling and Cabling the WAN Components
* Identify the components and connections necessary to allow WAN connections
like Frame Relay, and ISDN PRI from the central site to a branch office.
* Identify the components and connections necessary to allow WAN connections
like Frame Relay, and ISDN BRI from a branch office to the central site
* Identify the components and connections necessary to allow a WAN
connections like ISDN BRI from a telecommuter site to the central site
■.Configuring Asynchronous Connections to a Central Site with Modems
* Specify the commands and procedures necessary to configure an access
server for modem connectivity so telecommuters can access the central site.
* Specify the commands and procedures to configure the central site for dial
* Specify the commands used to reverse Telnet to the modem and configure the
* Specify the commands and procedures used to set up the modem
■.Configuring PPP and Controlling Network Access with PAP and CHAP
* Specify the commands and syntax used to configure a PPP connection between
* Specify the commands and syntax to configure PAP or CHAP authentication to
* Configure Multilink PPP to increase the data throughput.
* Specify the commands used to verify proper PPP configuration and
* Accessing the Central Site with Windows 95
* Specify the commands and procedures to configure a PC to complete a dialup
call to the central site router through the traditional telephone network.
■.Using ISDN and DDR Technologies to Enhance Remote Connectivity
* Identify when to use ISDN BRI and PRI services and select the service that
best suits a set of given requirements.
* Identify the Q.921 and Q.931 signaling and call setup sequences.
* Specify the commands used to configure ISDN BRI and PRI
* Specify the commands used to configure DDR
■.Optimizing the use of DDR Interfaces
* Specify or select appropriate dialup capabilities to place a call.
* Specify the commands and procedures to configure rotary groups and dialer
* Specify the commands used to verify proper dialer profile or rotary group
configuration and troubleshoot an incorrect configuration.
■.Using X.25 for Remote Access
* Specify the commands and procedures to configure an X.25 WAN connection
* Specify proper X.121 addresses and the commands used to assign them to
* Specify the commands and procedures used to verify proper X.25
configuration and troubleshoot incorrect X.25 configuration
■.Establishing a Dedicated Frame Relay Connection and Control Traffic Flow
* Specify the commands and procedures used to configure a Frame Relay WAN
connection between the central office and branch office
* Specify the commands to configure subinterfaces on virtual interfaces to
* Specify the commands used to configure Frame Relay traffic shaping.
* Specify the commands and procedures used to verify proper Frame Relay
configuration and troubleshoot an incorrect configuration
■.Enabling a Backup to the Permanent Connection
* Specify the procedure and commands used to configure a backup connection
* Specify the procedure and commands used to configure a backup connection
to activate when the primary line reaches a specified threshold.
* Specify the procedure and commands used to configure a dialer to function
■.Managing Network Performance with Queuing and Compression
* Determine why queuing is enabled, identify alternative queuing protocols
that Cisco products support, and determine the best queuing method to implement.
* Specify the commands to configure weighted-fair, priority and custom
* Specify the commands and procedures used to verify proper queuing
configuration and troubleshoot incorrect configuration
* Specify the commands and procedures used to effectively select and
■.Scaling IP Addresses with Network Address Translation
* Describe how NAT and PAT operate.
* Specify the commands and procedures to configure NAT and PAT to allow
reuse of registered IP addresses in a private network.
* Verify proper configuration of NAT and PAT with available Cisco
■.Using AAA to Scale Access Control in an Expanding Network
* Specify, recognize or describe the security features of CiscoSecure and
* Specify the commands and procedures used to configure a router to access a
* Specify the commands used to configure AAA on a router to control access
|
|
| 文章录入：skyuu 责任编辑：skyuu |
|
| 【字体：小 大】【发表评论】【加入收藏】【告诉好友】【打印此文】【关闭窗口】 |
用户登录
